HitPad Mini Manual
* When selecting input mode, you need to connect the device while pressing and holding the button below.
Settings for each mode
① Input mode
1P--PS3/D-input mode (Raspberry Pi/Android)
1K--Nintendo Switch Mode
2K--PC/Input Mode (Windows/Steam)
*Converter must be purchased separately.
*Mayflash magic boots are recommended.
For detailed settings, please see "Installation Process" below.
②Arrow key mode
* SELECT + START + ↓ = Arrow key mode (DP)
* SELECT + START + ← = Left stick mode
* SELECT + START + → = Right stick mode
③SOCD mode
SOCD simultaneous cleaning forces the controller to follow specific directional input rules when sending input to a PC or console. Users can select one of three SOCD modes while using the controller by pressing one of the following default button combinations:
*HOME + START + ↓ = Neutral mode
Up + Down = Neutral Left + Right = Neutral
*HOME + START + ↑ = Top priority mode
Up + Down = UP Left + Right = Neutral Standard stickless operation
*HOME + START + ← = Last input takes priority
④RGB mode
* SELECT + START + 1P Next backlight effect
* SELECT + START + 1K Previous backlight effect
* SELECT + START + 2P Brightness +
* SELECT + START + 2K Brightness
* SELECT + START + 3P LED parameter up
* SELECT + START + 3K LED parameter down
* SELECT + START + 4P on the pressed parameter
* SELECT + START + 4K Pressed parameter
Web Configurator
Press and hold the "START" button to connect the controller to your PC, then access http://192.168.7.1 in your web browser.
Launches a built-in web-based configuration application.
Key Table
|
mode
|
XINPUT
|
SWITCH
|
PS3
|
DINPUT
|
GP2040
|
|
1P
|
X
|
Y
|
■
|
1
|
B3
|
|
2P
|
Y
|
X
|
▲
|
4
|
B4
|
|
3P
|
RB
|
R
|
R1
|
6
|
R1
|
|
4P
|
LB
|
L
|
L1
|
5
|
L1
|
|
1K
|
A
|
B
|
×
|
2
|
B1
|
|
2K
|
B
|
A
|
〇
|
3
|
B2
|
|
3K
|
RT
|
ZR
|
R2
|
8
|
R2
|
|
4K
|
LT
|
ZL
|
L2
|
7
|
L2
|
|
SELECT
|
BACK
|
-
|
SELECT
|
9
|
S1
|
|
START
|
START
|
+
|
START
|
10
|
S2
|
|
LS
|
LS
|
LS
|
L3
|
11
|
L3
|
|
RS
|
RS
|
RS
|
R3
|
12
|
R3
|
|
HOME
|
XBOX
|
HOME
|
13
|
A1
|
|
|
TP
|
Screenshot
|
14
|
A2
|
TURBO
To set "Rapid Fire Mode," press and release the TURBO button while simultaneously pressing the button you want to set.
If you want to cancel after starting, just repeat the same operation to restore it to its original state.
- Rapid fire can be set to any of the following buttons: 1P, 2P, 3P, 4P, 1K, 2K, 3K, or 4K.
- The firing rate can be adjusted from 1 to 60 times per second (individual adjustment of the firing rate for each button is not supported).
- To increase the rate of fire, press the UP key while holding down the TURBO button. To decrease the rate of fire, press the DOWN key while holding down the TURBO button.
- Even when the power is turned off, the set firing speed will remain saved in the Maonboard memory, but the state of the rapid fire button will be reset the next time you start the game.